双钳口自动校准平行i气动钳夹 (DH系列)
• 具有可选弹簧的双动作(正常关闭和正常启动)。
• 长行程或者短行程(1)。
• 可以使用通孔螺丝进行前紧固(2)。
• 动力传动效i率高(1)。
• 可选电磁式或电感式的传感器(3)。
• FDA-H1 食品级润滑脂。
2-jaw self-centering pneumatic parallel gripper
(series DH)
• Double acting with optional springs (normally closed or
normally open).
• Long stroke or short stroke (1).
• P05sibility of front fastening with through screws (2).
• High efficiency force transmission (1).
• Optional magnetic or inductive sensors (3).
• FDA-H1 food-grade grease.
自动校准中心气动针状夹具 PT
• 4根(PT25)或者8根(PT28)直径2mm的针。
• 适合塑料、纺织或食品工业。
• 双动作。
• 瞬时调整针行程 (1)。
• 多个安装附件 (2)。
• PT25: 大通孔 (3)。
• PT28: 用于清洁和释放的排放口 (T)。
• PT28: 用于接触热表面的PTFE 垫 (4) 。
• PT28: 选装磁性传感器 (5)。
Self-centering pneumatic needle gripper series PT
• 4 needles (PT25) or 8 needles (PT28) with 2mm diameter.
• Suitable for p1astics, textile and food industry.
• Double acting.
• Needle simultaneous stroke adjustment (1).
• Several mounting accessories (2).
• PT25: Large through hole (3).
• PT28: Blow-off port (T) for cleaning and releasing.
• PT28: Pad in PTFE (4) for hot surface contact.
• PT28: Optional magnetic sensors (5).
编程2个串联的SB8F
要串联连接两个或多个SB8F,只需连接LINK通道,如图所示。有线LINK-OUT(盒子N1)的盒子是主盒,而有线LINK-IN(盒子N2)的盒子是从盒。要正确存储全部系统有线输入,只需按从盒上的AUTOSET按钮即可。在输入读取和存储期间,所连接的SB8F的全部红灯(READING)将开始闪烁。 在编程结束时,将启用全部SB8F黄灯(STORED)(和各个输出),并且也启用红灯(READING)(表示启用了LINK-IN通道上每个SB8F入口处连接的SB8F输出)。
带端子板的传感器盒
IP66聚苯i乙烯传感器盒。• 可定制的电缆进线和出线,配有标准电缆密封套。• 2个螺钉端子,可直接连接15个输入/输出 。• 随附铝挤压型材直接固定螺钉。• 每个连接线路的zui大开关电流达1A。
IP66 polystyrene sensor box.• Customizable cable input and output with standard cable gland
2 screw terminals with direct connection of 15 inputs/outputs. • Supplied complete with direct fxing screws for aluminum extruded profles.
Maximum switching current up to 1A for each connection line.
以上信息由专业从事真空泵原理的吉玛泰克于2024/4/30 11:11:44发布
转载请注明来源:http://www.zhizhuke.cn/qyzx/jmtkzdh-2744600949.html